以前國內的熱流道取暖器都是進口的，但是進口的熱流道取暖器購買周期長，價格高，售后無人處理。 目前我廠生產的熱流道加熱器已被國內多家廠家采用，加熱效果好，使用壽命長。 熱流道加熱器(彈簧加熱環)是目前注塑機噴嘴最理想的電加熱器。 熱流道加熱器的原理: 原理是厚金屬在……

The integral hot runner system is a small part used in a multi-cavity injection mold with a thimble type nozzle. When the spacing between the axis of the small nozzle is 10-20mm, the nozzle is connected to the runner plate with threads, resulting in the h

針閥式熱流道熱嘴是工業產品中的一種，主要用于閥澆口熱流道系統閥針傳動安裝，熱流道系控制閥針的開、閉運動。相當于一只液壓油缸，應用注射機的液壓安裝與模具銜接，構成液壓回路，完成閥針的開、閉運動，控制熔融狀態塑料注入型腔。 熱流道閥針式熱嘴裝置需要注意的事項有以下幾點： 1、裝置前需清算各個熱咀……

溫控箱是一種持續堅持所需溫度值的設備,它主要經過表芯內聰慧電腦晶片(MCU)探測發熱流道溫度,再經過聰慧電腦內部材料處置,輸出恰當比例電流值,從而到達控溫目的 　　溫控箱模組主要功用： 　　1、適用于電壓110-240VAC及頻率（60HZ／50HZ）可轉換。 　　2、微電腦P……

A successful hot runner system mold application project requires several steps to ensure: 1. Select the right hot runner supplier. As a plastic mold factory and plastic products injection factory, plastic products from which aspect? What about the

熱流道系統是多腔注射模的關鍵部件。相反，從模具制造商的角度來看，熱流道可能是最難理解的模具元件。實際上，熱流道系統是非常復雜的，包括機械作用、加熱技術和精密制造等方面的內容。熱流道系統在成型環境中的成功應用，需要對噴孔設計、型腔幾何、樹脂和模具工進行詳細的分析。 在初步應用分析期間，應評估以下問題： （1）……

Production, operation and maintenance of hot runner system: （1） Preparation The mould worker connects the cooling water channels of the moving mould, the fixed mould and the hot half mould. If the temperature requirements on both sides of the dy

First, according to the plastic structure and use requirements, determine the inlet location. As long as the plastic structure permits, the nozzle and nozzle head in the fixed mold insert block will not interfere with the formed structure, then the feed p

1.什么是熱流道技術？ 　　熱流道技術確保流道和澆口中的塑料通過加熱保持熔融狀態。由于流道附近或中心有加熱棒和加熱環，從注塑機料筒出口到澆口的整個流道處于高溫狀態，使流道內的塑料保持熔融狀態。一般停機后不需要打開轉輪取出冷凝水，重啟時只需要將轉輪加熱到需要的溫度即可。簡而言之，熱流道是注塑機料筒的延伸。 ……

熱流道溫控箱的原理及性能 　　溫控箱是一個持續保持所需溫度的裝置。熱流道的溫度主要由監控核心中的智.能計算機芯片(mcu)檢測，然后對智.能計算機的內部數據進行處理。溫度控制的精度和穩定性主要取決于以下幾個重要因素:采樣周期參數、確定溫度的數據濾波、測量電路的溫度補償決定溫度測量精度的控制:通過調節輸出電……

One，The residue at the gate is prominent or drooling and the appearance is poor 　　1. Main reason 　　 Unreasonable gate structure selection, improper temperature control, large residual pressure in the melt in the runner after injection.

The multi-cavity open point gate (point gate) hot runner system is prone to problems during the production process. The main reason is that the outer diameter of the hot nozzle is relatively small, the number of cavities is large, and the gate is small. T